Tap on Push notification to connect automaticly

Sato

It's still not working properly. What I can see is that whenever Esp sends a notification, it freezes for about 5...10 seconds then it continues to communicate. I can see it on the led on the pcb board, which is always flashing as long as I have an internet connection.
With version 6.0 this didn't happen, it didn't freeze when sending a push notification.
Another issue is that the app now freezes so often that I have to force it to stop.
I haven't changed the App settings, the Mqtt clientid is still Not set

Regards

Sato

@kl3m3n

Yes, right allways the Esp send the Push notification

kl3m3n

@Sato What freezes? GUI-O app or ESP? Both?

Can you try setting the clientId to something unique and reconnect (disable and enable IoT notifications)? And see if the problem persists?

Sato

Hi @kl3m3n,

The problem perssist
Have set the client id to 1234, disable notification and enabled it again
Have reinitalize the Smartphone
The most notification don´t arrive

The Clear All continue not to clear the notifications buffer, but that is a other issue
that have nothing to do with the problem, i think

Is it possible to update back to 6.0 to make tests again?

Regards

kl3m3n

@Sato Hi.

I have tested (again) the IoT push notifications and I cannot reproduce none of the problems you are experiencing.

I receive all notifications that I sent (with QOS level 1 or 2, I get them even if notifications are disabled and I enable them).
It works if I set the clientId or keep it empty.
The number of notifications shown corresponds to the setting "Notifications to show". When the set number of notifications are reached, the oldest is pushed out.
If I press "CLEAR ALL", all notifications are cleared

I will try it on other Android devices and using ESP32.

If I remember correctly you've had some similar problems with notifications in the past and I as far as I remember I did not do any fixes then.

Can you try another Android device?

Regards.
Kl3m3n

Sato

Hi @kl3m3n,

Tomorrow I'll test it with another Esp32 and another cell phone and give you feedback

Yes, when I press Clear All the notifications disappear, but when the next notification arrives the others that already existed before pressing Clear All appear again, shouldn't only the last one appear since I supposedly "deleted" the previous ones?

Regards

kl3m3n

@Sato said in Tap on Push notification to connect automaticly:

Yes, when I press Clear All the notifications disappear, but when the next notification arrives the others that already existed before pressing Clear All appear again, shouldn't only the last one appear since I supposedly "deleted" the previous ones?

I cannot reproduce it. When I "CLEAR ALL" and send a new notification, only the new one appears.
Are you sure you are not storing and sending old notifications on ESP side?

Can you give exact steps for this? So I will try to follow them with my tests? Also for other tests, can you give steps so I can try to reproduce the exact steps?

Best regards.

Sato

Hi @kl3m3n,

Strange, I'm shure that only one Push will be send every time.

I'll check it tomorrow on the serial monitor too

Regards

kl3m3n

@Sato
FYI - I use this for testing MQTT:

https://mqttx.app/

It's free and it's easy to setup. You can get the credentials from the example. Use 1883 port without SSL.

Sato

Hi @kl3m3n,

Thank you
Im moment i not know how to use it with the esp.

Regards

Sato

Hi @kl3m3n,

Sorry, sorry. The problem is solved, it was the Spiffs on my Esp32. Now it works.

Best regards

kl3m3n

@Sato said in Tap on Push notification to connect automaticly:

Hi @kl3m3n,

Sorry, sorry. The problem is solved, it was the Spiffs on my Esp32. Now it works.

Best regards

Which problem is solved?

The GUI-O application freezing?
The "CLEAR ALL" button?

Can you briefly explain?

Thanks.

Regards,
Kl3m3n

kl3m3n

@Sato said in Tap on Push notification to connect automaticly:

Hi @kl3m3n,

Thank you
Im moment i not know how to use it with the esp.

Regards

I meant for testing the GUI-O MQTT functionalities (e.g., IoT push notifications), before implementing your application on ESP.

You could of course also use this with ESP...

Sato

Hi @kl3m3n,

When Esp detects a fault on some of the selected pins, it appent the fault to a SPIFFS file and also sends a push notification. What was happening, I'm not sure why, was that writing to the file was taking so long that most of the time Mqtt communication would stop working during this period and when it was re-established Esp had already sent the notification and so I no longer received it on Gui-O. After reloading the virgin files back into SPIFFS, it worked again.
On the subject of Clear All, I've seen that it works after opening the App, so I think that's fine.
Again, I'm sorry to have been bothering you with this problem, which turned out to be on my end, but it coincided with the update of the App version and that led me to think that this problem came from there.
This has also served to learn a little more.

Thanks for your support

Regards

kl3m3n

@Sato Thank you for the explanation.

I am glad you've sorted it out!

Best regards.

kl3m3n

@Sato Hi.

I cannot add the feature you suggested.

But I've implemented device filtering by name. This should help.

See version 1.0.66.

Best regards,
Klemen

Sato

@kl3m3n,

Ok, thank you. I will see it tomorrow

Regards

Sato

Hello @kl3m3n,

Works good, thank you

Regards